Starting a Frigidaire dishwasher is a simple process that can be completed in just a few easy steps. First, make sure that the dishwasher is properly connected to the water supply and power outlet. Next, open the dishwasher door and locate the control panel. The control panel will typically be located on the top or front of the dishwasher door.
Once you have located the control panel, press the “Start” button. The dishwasher will begin to fill with water and the wash cycle will start. The wash cycle will typically last for about 2 hours, but may vary depending on the selected cycle. Once the wash cycle is complete, the dishwasher will drain the water and the drying cycle will begin. The drying cycle will typically last for about 30 minutes, but may vary depending on the selected cycle.
Once the drying cycle is complete, the dishwasher will automatically shut off. You can then open the dishwasher door and remove the clean dishes. If you have any questions about how to start a Frigidaire dishwasher, please consult the user manual or contact Frigidaire customer service.
Unpack and Inspect the Dishwasher
Before you can start using your Frigidaire dishwasher, you need to unpack it and inspect it for any damage. Here’s how to do it:
1. Unpack the dishwasher.
Carefully remove the dishwasher from its packaging. Be sure to lift it from the bottom, not the door. Once the dishwasher is out of the box, remove all of the packing materials, including the styrofoam insert and the plastic wrap on the door.
2. Inspect the dishwasher for damage.
Once the dishwasher is unpacked, inspect it for any damage. Look for any dents, scratches, or cracks in the exterior of the dishwasher. Also, check the interior of the dishwasher for any damage to the racks, basket, or door seal.
If you find any damage, do not use the dishwasher. Contact Frigidaire customer service for assistance.
Inspect the Power Cord and Water Supply Line
Once you have inspected the dishwasher for damage, check the power cord and water supply line to make sure they are in good condition.
The power cord should be free of any damage or fraying. The water supply line should also be free of any damage or leaks.
If you find any damage to the power cord or water supply line, do not use the dishwasher. Contact Frigidaire customer service for assistance.
Check the Dishwasher’s Drain Hose
The dishwasher’s drain hose should be connected to the drainpipe under your sink. Make sure that the drain hose is properly connected and that it is not kinked or blocked.
If the drain hose is not properly connected or if it is kinked or blocked, the dishwasher will not be able to drain properly.
Determine Water and Electrical Connections
Water Connections
Firstly, ensure that the dishwasher is located near a water supply and drain. You’ll need a cold water supply line connected to a faucet or valve. Inspect the dishwasher’s hoses for any damage or leaks. The hoses should be securely attached to both the dishwasher and the water supply. Additionally, there should be a drainpipe connected to the dishwasher’s drain port, ensuring that the water can be properly discharged.
Electrical Connections
Next, verify that the dishwasher has an adequate electrical connection. It must be connected to a dedicated circuit with the appropriate voltage and amperage rating. The circuit should be protected by a circuit breaker or fuse that is the right size for the dishwasher’s amperage draw. Ensure that the power cord is undamaged and properly plugged into a grounded outlet. It’s also important to have a grounded electrical system to prevent the risk of electrical shock. For more specific details, consult the dishwasher’s manual.
| Required Voltage and Amperage |
|---|
| 120 volts @ 60 Hz |
| 15-amp circuit |
Install the Dishwasher in the Cabinet
Before installing your Frigidaire dishwasher, make sure you have the proper tools and materials: a level, a screwdriver, a wrench, and plumber’s tape. Follow these steps to install your dishwasher:
1. Prepare the Cabinet
Remove the old dishwasher or any existing shelves or drawers that may interfere with the installation. Ensure the cabinet opening is the correct size for the new dishwasher.
2. Connect the Water Supply
Locate the water supply line under the sink and connect it to the dishwasher’s water inlet valve using a flexible hose and plumber’s tape. Tighten the connections securely.
3. Connect the Drain Hose
Identify the drain hose coming from the sink garbage disposal or drainpipe. Connect the dishwasher’s drain hose to the drain hose using the provided clamp or adapter. Ensure a snug fit to prevent leaks.
| Tools and Materials | Quantity |
|---|---|
| Level | 1 |
| Screwdriver | 1 |
| Wrench | 1 |
| Plumber’s tape | 1 roll |
| Flexible hose | 1 |
| Clamp or adapter | 1 |
Level and Secure the Dishwasher
To level your dishwasher, you will need to adjust the feet at the bottom of the dishwasher. Use a level to ensure that the dishwasher is level from front to back and side to side. Once the dishwasher is level, tighten the feet to secure it in place.
To secure the dishwasher to the countertop, you will need to use the mounting brackets that came with the dishwasher. The mounting brackets will attach to the underside of the countertop and the top of the dishwasher. Once the mounting brackets are in place, tighten the screws to secure the dishwasher to the countertop.
If you are not comfortable leveling and securing the dishwasher yourself, you can call a qualified appliance repair technician to do it for you.
Additional Tips for Leveling and Securing the Dishwasher
- Make sure that the floor is level before you start leveling the dishwasher.
- Use a level that is at least 24 inches long to ensure accuracy.
- Tighten the feet of the dishwasher until they are snug, but do not overtighten them.
- Secure the dishwasher to the countertop using the mounting brackets that came with the dishwasher.
- If you are not comfortable leveling and securing the dishwasher yourself, call a qualified appliance repair technician to do it for you.
| Leveling the Dishwasher | Securing the Dishwasher |
|---|---|
| Use a level to ensure that the dishwasher is level from front to back and side to side. | Use the mounting brackets that came with the dishwasher to secure it to the countertop. |
| Tighten the feet of the dishwasher until they are snug, but do not overtighten them. | Tighten the screws to secure the dishwasher to the countertop. |
Connect the Water Supply Line
Connecting the water supply line to your Frigidaire dishwasher is a crucial step in the installation process. Here’s a detailed guide to help you do it right:
1. Shut Off the Water Supply
Turn off the water supply valve located under the sink, which is connected to the cold water line.
2. Locate the Dishwasher Inlet Valve
On the back of the dishwasher, locate the inlet valve where the water supply line will be attached.
3. Install the Inlet Gasket
A gasket is usually included in the dishwasher kit. Slide it onto the end of the water supply line.
4. Attach the Water Supply Line
Connect the end of the water supply line with the installed gasket to the inlet valve on the dishwasher. Tighten it securely by hand. Avoid using excessive force, as it can damage the valve.
5. Test for Leaks
Turn on the water supply valve under the sink and inspect the connection for any leaks. If you notice any water dripping, tighten the connection further. Leave the water turned on for a few minutes to ensure no leaks occur.
Additional Tips
To prevent potential leaks, use a new water supply line, as old lines can wear out and develop cracks.
Check the water supply line periodically for any signs of damage.
If you experience any difficulties connecting the water supply line, don’t hesitate to contact a qualified plumber for assistance.
Connect the Drain Hose
The drain hose is responsible for draining wastewater from the dishwasher. It is usually a white or gray plastic hose that connects to the drainpipe under the sink. To connect the drain hose, follow these steps:
- Locate the drainpipe under the sink. It is usually a white or black plastic pipe with a threaded end.
- Attach the drain hose to the drainpipe. Make sure the connection is tight and secure.
- Place the other end of the drain hose into the dishwasher’s drain pump. The drain pump is usually located at the bottom of the dishwasher, near the back.
- Secure the drain hose to the drain pump. Use a hose clamp or other method to make sure the connection is tight and secure.
- Test the drain hose by running a test cycle. The dishwasher should drain the water properly.
- If the dishwasher does not drain properly, check the following:
- Locate the shut-off valves under the kitchen sink or behind the dishwasher.
- Turn the valves clockwise to open them fully.
- Run the water from the faucet to clear any trapped air in the lines.
- Check for leaks around the connections.
- If the water supply is not turned on, the dishwasher will not start.
- A slow-moving water supply may indicate a clogged inlet valve or filter.
- Check the water pressure by attaching a pressure gauge to the cold water line. A pressure below 20 psi may require a booster pump.
- Load the dishwasher. Arrange the dishes in the dishwasher so that they do not block the water jets.
- Add detergent. Add the recommended amount of dishwasher detergent to the detergent dispenser.
- Close the door. Make sure the door is securely closed.
- Select a cycle. Select the appropriate cycle for the type of dishes you are washing.
- Press the start button. The dishwasher will start filling with water and washing the dishes.
People Also Ask About How To Start Frigidaire Dishwasher
Where is the start button on a Frigidaire dishwasher?
The start button is located on the front of the dishwasher, typically on the bottom right side.
How do I know if my Frigidaire dishwasher is running?
You can tell if your Frigidaire dishwasher is running by listening for the sound of water running and the motor. You can also look at the control panel to see if the lights are on and the cycle is progressing.
What do I do if my Frigidaire dishwasher won’t start?
If your Frigidaire dishwasher won’t start, check to make sure that the door is securely closed, the power is on, and the water supply is turned on. You can also try resetting the dishwasher by unplugging it for a few minutes and then plugging it back in.
| Possible Problem | Solution |
|---|---|
| The drain hose is kinked or blocked. | Un kink or unblock the drain hose. |
| The drainpipe is clogged. | Un clog the drainpipe. |
| The drain pump is not working. | Replace the drain pump. |
Install the Electrical Power Cord
Installing the electrical power cord for your Frigidaire dishwasher is a crucial step in the installation process. Here’s a detailed guide to help you complete this task safely and effectively:
1. Locate the Power Cord: The electrical power cord should be included with your dishwasher and typically comes pre-attached. However, if it’s detached, locate the power cord outlet on the back of the dishwasher and make sure the cord is properly connected.
2. Pull the Cord Through the Opening: There should be a hole or opening in the dishwasher’s base where the power cord can be pulled through. Carefully guide the cord through this opening, making sure it doesn’t get pinched or damaged.
3. Align the Cord with the Outlet: Once the power cord is pulled through, align it with the electrical outlet. Ensure that the cord is not twisted or tangled, as this could create a fire hazard.
4. Connect the Power Cord: Insert the power cord’s prongs into the electrical outlet. Make sure they fit securely and that the connection is tight.
5. Secure the Cord: Once the power cord is connected, use the provided strain relief to secure the cord to the dishwasher. This prevents the cord from being accidentally pulled out.
6. Check for Loose Wires: Ensure that there are no loose wires or connections around the power cord or outlet. Any loose wires could pose a safety hazard.
7. Power Up the Dishwasher: After completing these steps, power up the dishwasher by turning on the circuit breaker or fuse that controls the dishwasher’s power supply. If the dishwasher powers up successfully, you have successfully installed the electrical power cord.
Turn On the Water Supply
Before turning on your Frigidaire dishwasher, ensure the water supply is turned on. This ensures an adequate water flow during the wash cycle.
Steps to Turn On the Water Supply:
Troubleshooting:
| Valve Location | Turn Direction |
|---|---|
| Under sink | Clockwise |
| Behind dishwasher | Counterclockwise |
Check for Leaks and Test the Dishwasher
Step 1: Check for Leaks
After connecting the dishwasher, run an empty cycle to check for leaks. Place a towel under the dishwasher and observe it for any water seepage.
Step 2: Load the Dishwasher
Fill the top rack with glasses, cups, and small dishes. Place plates and other large items in the bottom rack. Ensure that dishes are placed upright and don’t overlap, allowing water to circulate freely.
Step 3: Add Detergent
Fill the detergent dispenser according to the manufacturer’s instructions. Use a high-quality dishwasher detergent for optimal cleaning.
Step 4: Select a Wash Cycle
Choose the appropriate wash cycle for the type of dishes you are washing. For heavily soiled dishes, opt for a heavy-duty cycle. For lighter loads, use a normal cycle.
Step 5: Start the Dishwasher
Press the start button to initiate the wash cycle. The dishwasher will fill with water and begin washing the dishes.
Step 6: Observe the Dishwasher During Operation
Monitor the dishwasher during the first few minutes of operation to ensure it is filling and draining properly. Listen for any unusual noises or vibrations.
Step 7: Check the Dishes After Completion
Once the wash cycle is complete, open the dishwasher door and examine the dishes. They should be clean and dry, with no residual food particles or soap scum.
Troubleshooting Common Issues
If you encounter any problems with your dishwasher, refer to the following table for troubleshooting tips:
| Problem | Possible Cause | Solution |
|---|---|---|
| Dishwasher won’t start | Power outage or disconnected power | Check power supply and reconnect if necessary |
| Dishes not clean | Clogged filters or spray arms | Clean filters and spray arms as per manufacturer’s instructions |
| Water leaking | Damaged gasket or loose hoses | Inspect and replace damaged components as necessary |
Set the Dishwasher Controls
Once you have loaded your dishwasher and added the appropriate detergent, you can now set the controls to start the wash cycle.
1. Turn on the Dishwasher
Press the “Power” button to turn on the dishwasher. The display will light up and show the current settings.
2. Select a Wash Cycle
Use the cycle selection buttons to choose the desired wash cycle. Common cycles include “Normal,” “Heavy,” and “Light.”
3. Set the Temperature
Press the temperature buttons to select the desired wash temperature. Higher temperatures are best for heavily soiled dishes.
4. Choose an Option (Optional)
Depending on your dishwasher model, you may have additional options available. These could include “Sanitize,” “Extra Rinse,” or “Delay Start.”
5. Start the Dishwasher
Once all the settings are selected, press the “Start” button to begin the wash cycle. The dishwasher will start filling and washing the dishes.
6. Check the Progress
You can monitor the progress of the wash cycle by checking the display. It will show the remaining time and any error codes that may occur.
7. Unload the Dishwasher
Once the cycle is complete, the dishwasher will beep or display a message indicating the dishes are ready. Unload the dishwasher promptly to prevent drying issues.
Advanced Settings
Some Frigidaire dishwashers offer advanced settings that allow for customization of the wash cycle. These settings may include:
| Setting | Description |
|---|---|
| Half Load | Reduces water and energy consumption for smaller loads. |
| Soil Sensor | Automatically adjusts wash settings based on the soil level of the dishes. |
| Child Lock | Prevents accidental changes to the settings while the dishwasher is running. |
How To Start Frigidaire Dishwasher
To start a Frigidaire dishwasher, follow these steps:
