Are you having trouble setting your Armitron watch? Don’t worry, it’s a relatively simple process that can be done in just a few minutes.
First, you’ll need to locate the two buttons on the side of the watch. The top button is the “Mode” button, and the bottom button is the “Set” button. To set the time, press the “Mode” button until the time display starts flashing. Then, use the “Set” button to adjust the hours and minutes. Once you have the correct time, press the “Mode” button again to save your changes.
To set the date, press the “Mode” button until the date display starts flashing. Then, use the “Set” button to adjust the month, day, and year. Once you have the correct date, press the “Mode” button again to save your changes. Additionally, you can also set the alarm, time zone, and other settings by following the same process and using the corresponding buttons. Consult your watch’s user manual for specific instructions on setting other functions.
Familiarize Yourself with the Watch’s Functions
Armitron watches are known for their user-friendly design and intuitive controls. Before embarking on the time-setting process, take some time to familiarize yourself with the watch’s functions:
**1. Buttons and Dials:**
| Button | Function |
|---|---|
| Upper Left | Mode selection (chronograph, countdown timer, etc.) |
| Lower Left | Reset/Start/Stop functions for the current mode |
| Upper Right | Adjust hour or day of the week |
| Lower Right | Adjust minutes, month, or year |
2. Display Screen:
The watch’s display screen typically displays the current time, date, day of the week, and other relevant information depending on the selected mode.
3. Crown:
The crown is a small knob located on the side of the watch. It is used to manually wind the watch (for mechanical watches) and to set the time and date.
Locate the Time and Mode Buttons
The Armitron watch has two buttons on the right side of the watch face. The top button is the mode button and the bottom button is the time button. These buttons are used to set the time, date, and other features of the watch.
Mode Settings:
The mode button cycles through the watch’s different modes, including the time, date, alarm, and chronometer modes. To access a specific mode, press the mode button repeatedly until the desired mode is displayed.
Time Button Functions:
The time button has three main functions:
| Function | Action |
|---|---|
| Adjust hour | Press and hold the time button for 3 seconds, then press the mode button to adjust the hour. |
| Adjust minute | Press and hold the time button for 3 seconds, then press the time button to adjust the minute. |
| Adjust second | Press and hold the time button for 3 seconds, then press the mode button twice to adjust the second. |
Note: When adjusting the time, make sure to press the mode or time button to confirm your changes before releasing it.
Adjust the Time Zone
When traveling across different time zones, it is crucial to adjust your watch to the local time. The Armitron watch provides a simple and convenient way to do this. Follow these steps to accurately set the time zone:
Determine Your Destination’s Time Zone
Before adjusting your watch, determine the time zone of your destination. You can use online resources, such as timeanddate.com, to find the time difference between your current location and the place you will be traveling to.
Locate the Time Zone Adjustment Buttons
On the side of the Armitron watch, you will find two buttons labeled “TZ” or “Time Zone.” These buttons allow you to manually adjust the time zone.
Set the Correct Time Zone
To change the time zone, follow these steps:
- Press and hold the “TZ” button until the time zone indicator on the display starts flashing.
- Use the other “TZ” button to scroll through the available time zones.
- Once you find the correct time zone, release the button to confirm the change.
The Armitron watch will now display the correct time and date for your destination’s time zone.
Set the Date and Day
Setting the date and day on your Armitron watch is simple. Here are the steps:
1. Enter Date and Day Setting Mode
Pull the crown out to the first click position. This will enter the date and day setting mode.
2. Set the Date
Rotate the crown clockwise to advance the date. Rotate the crown counterclockwise to decrease the date.
3. Set the Day
Once you have set the date, rotate the crown counterclockwise to adjust the day of the week. The day of the week will appear in the smaller subdial.
4. Set the 12/24 Hour Display
Some Armitron watch models allow you to switch between a 12-hour and 24-hour display. To do this, you need to enter the time setting mode (see below) and then pull the crown out to the second click position. Rotate the crown to select between “AM” and “PM” (if you are using the 12-hour display) or “24H” (if you are using the 24-hour display).
| Time Format | 12-Hour Display | 24-Hour Display |
|---|---|---|
| AM/PM | 12:00 PM | – |
| 24H | – | 12:00 |
5. Exit Date and Day Setting Mode
Once you have finished setting the date and day, push the crown back into its original position to exit date and day setting mode.
Configure Alarms and Timers
Armitron watches offer versatile features, including alarms and timers. To set these functions, follow these steps:
Alarms
1. Press the “Mode” button until the Alarm mode is displayed.
2. Press the “Adjust” button to enter setting mode.
3. Use the “+” and “-” buttons to set the hour and minutes for the alarm.
4. Press the “Adjust” button to confirm the setting.
5. Repeat steps 2-4 to set multiple alarms (up to 5).
Timers
1. Press the “Mode” button until the Timer mode is displayed.
2. Press the “Set” button to start setting the timer.
3. Use the “+” and “-” buttons to set the duration of the timer.
4. Press the “Set” button to confirm the setting.
5. Press the “Start/Stop” button to start or stop the timer.
| Feature | Button Sequence |
|---|---|
| Set Alarm 1 | Mode > Adjust > +/-> Adjust |
| Set Alarm 2 | Mode > Adjust > +/-> Adjust |
| Set Alarm 3 | Mode > Adjust > +/-> Adjust |
| Set Timer | Mode > Set > +/-> Set |
| Start/Stop Timer | Start/Stop |
Utilize the Backlight Function
The backlight illuminates the watch face for easy viewing in low-light conditions. To activate the backlight, press and hold the “Light” button located on the side of the watch. The backlight will remain illuminated for approximately five seconds before automatically turning off to conserve battery power.
Understanding the Backlight Settings
Some Armitron watches offer customizable backlight settings. You can configure the intensity, duration, and activation method of the backlight. To access these settings, consult your watch’s user manual.
Troubleshooting the Backlight
If the backlight is not functioning properly, try the following steps:
| Issue | Solution |
|---|---|
| Backlight does not illuminate | Replace the watch battery. |
| Backlight stays on continuously | Press the “Light” button again to turn off the backlight. |
| Backlight is dim or flickering | Clean the sensor located on the back of the watch with a soft cloth. |
Calibrate the Compass
To ensure accurate compass readings, it’s essential to calibrate the compass periodically. Here’s a step-by-step guide on how to calibrate your Armitron watch:
Step 1: Enter Calibration Mode
- Press and hold the “Mode” button until the “CAL” indicator appears on the display.
- Release the button.
Step 2: Rotate the Watch Slowly
- Slowly rotate the watch in a figure-eight pattern, keeping the watch parallel to the ground.
- Continue rotating for approximately 30 seconds.
Step 3: Rotate the Watch Vertically
- Hold the watch vertically, with the display facing upwards.
- Slowly rotate the watch 360 degrees.
Step 4: Repeat Step 2
- Repeat step 2 by rotating the watch in a figure-eight pattern again.
- Ensure you keep the same speed and direction as before.
Step 5: Exit Calibration Mode
- Press the “Mode” button to exit calibration mode.
- The “CAL” indicator will disappear, and the watch will display the time.
Tips for Accurate Calibration:
- Calibrate the compass in an open area away from magnetic fields or metal objects.
- Move the watch smoothly and consistently during the calibration process.
- Repeat the calibration process if the compass readings appear inaccurate.
| Calibration Movement | Time Duration |
|---|---|
| Figure-eight pattern | 30 seconds |
| Vertical rotation | 360 degrees |
| Figure-eight pattern (repeat) | 30 seconds |
Care and Maintenance
To ensure the longevity and optimal performance of your Armitron watch, proper care and maintenance are essential. Here are some guidelines to follow:
1. Keep it Clean: Regularly wipe down your watch with a soft, non-abrasive cloth to remove dirt and debris. For stubborn grime, use a mild soap solution. Avoid using harsh chemicals or detergents.
2. Protect from Water: Most Armitron watches are water-resistant, but it’s best to avoid submerging them in water. If your watch comes in contact with water, dry it thoroughly with a soft cloth.
3. Avoid Extreme Temperatures: Exposing your watch to extreme temperatures (both hot and cold) can damage the movement and other components.
4. Handle with Care: Avoid dropping or banging your watch against hard surfaces. Sudden impacts can cause damage.
5. Replace Battery Regularly: The battery in your Armitron watch will eventually need to be replaced. If you notice the watch running slowly or stopping prematurely, it’s likely time for a new battery.
6. Get Professional Service: For major repairs or maintenance tasks, it’s recommended to consult a professional watchmaker.
7. Store Properly: When not in use, store your Armitron watch in a cool, dry place, away from direct sunlight.
8. Avoid Magnetic Fields: Exposure to strong magnetic fields can disrupt the watch’s accuracy.
9. Clean the Band: If your watch has a metal band, use a soft brush or cloth to remove dirt and grime. If the band is leather, wipe it down with a damp cloth.
10. Follow the Water Resistance Guidelines: Armitron watches are water-resistant to different depths. Refer to the user manual or consult the Armitron website to determine the water resistance rating of your specific model and follow the corresponding usage recommendations. Here are some common water resistance ratings and their meanings:
| Rating | Meaning |
|---|---|
| Water Splash Resistance | Can withstand splashes of water, but not submersion |
| 30 Meters (3 ATM) | Can withstand immersion in water up to 30 meters (98 feet) |
| 50 Meters (5 ATM) | Can withstand immersion in water up to 50 meters (164 feet) |
| 100 Meters (10 ATM) | Can withstand immersion in water up to 100 meters (328 feet) |
| 200 Meters (20 ATM) | Can withstand immersion in water up to 200 meters (656 feet) |
How to Set an Armitron Watch
Armitron watches are known for their stylish designs and affordable prices. They’re also relatively easy to set, though the process can vary slightly depending on the model you have. Here are the general steps:
- Pull the crown out to the first position. This will stop the second hand and allow you to set the time.
- Turn the crown clockwise to set the hour hand to the correct hour.
- Pull the crown out to the second position. This will allow you to set the minute hand and date.
- Turn the crown clockwise to set the minute hand to the correct minute.
- Pull the crown out to the first position. This will stop the second hand and allow you to set the date.
- Turn the crown clockwise to set the date to the correct day.
- Push the crown back in to the normal position.
Once you’ve set the time and date, your watch is ready to wear.
People Also Ask
How do I set the time on my Armitron watch with a digital display?
To set the time on an Armitron watch with a digital display, press the “Mode” button until you reach the “Time” setting. Then, use the “+” and “-” buttons to adjust the hour and minute. Once you’ve set the correct time, press the “Mode” button again to save your changes.
How do I set the alarm on my Armitron watch?
To set the alarm on an Armitron watch, press the “Alarm” button. Then, use the “+” and “-” buttons to adjust the hour and minute. Once you’ve set the correct time, press the “Alarm” button again to save your changes. The alarm will sound at the time you’ve set, even if the watch is turned off.
How do I change the battery in my Armitron watch?
To change the battery in an Armitron watch, you’ll need a small Phillips head screwdriver. First, remove the four screws on the back of the watch. Then, carefully pry open the back of the watch and remove the old battery. Replace it with a new battery of the same type, and then close the back of the watch and tighten the screws.
