Badger garbage disposals are a common sight in many homes. They are known for their durability and efficiency, but even the best garbage disposals can eventually need to be replaced. If you are considering removing a Badger garbage disposal, there are a few things you need to know. First, you will need to disconnect the power to the disposal. This can be done by turning off the breaker that supplies power to the kitchen. Once the power is disconnected, you can begin to remove the disposal.
To remove the disposal, you will need to first remove the mounting bolts that hold it in place. These bolts are typically located on the bottom of the disposal. Once the bolts are removed, you can carefully lift the disposal out of the sink. Be sure to support the disposal with your other hand as you lift it out. Once the disposal is out of the sink, you can disconnect the drain line and the power cord.
Now that the disposal is disconnected, you can dispose of it. Most garbage disposals can be disposed of in the trash. However, you may need to check with your local waste management company to see if there are any special disposal requirements. Once the disposal is disposed of, you can install a new one. To install a new disposal, simply follow the instructions that came with the new unit. Be sure to connect the drain line and the power cord before turning on the power to the new disposal.
Gather Essential Tools
Before embarking on the task of removing your Badger garbage disposal, it is crucial to gather all the necessary tools to ensure a smooth and safe process. The following is a comprehensive list of essential tools you will need:
Wrench
An adjustable wrench is the primary tool for disconnecting the discharge tube and the mounting bolts that secure the disposal to the sink. Choose a wrench with a comfortable grip and sufficient leverage to loosen tight bolts.
Pliers
A pair of slip-joint pliers is essential for removing the electrical wire connectors from the disposal’s motor. They provide a secure grip and prevent damage to the wires while disconnecting them.
Screwdriver
A screwdriver is required to remove the screws holding the dishwasher drain hose to the disposal’s dishwasher port. A Phillips head screwdriver is typically used for this task.
Bucket
A bucket is necessary to collect any water or debris that may spill out during the removal process. It also provides a convenient place to store the removed parts temporarily.
Flashlight
A flashlight is helpful for illuminating the disposal’s underside and for reaching into tight spaces during disassembly. It enhances visibility and allows you to work more effectively.
Other Tools
Additional tools that may be required for specific models or situations include a putty knife, a flashlight, and a pair of gloves for hand protection. Preparing with the appropriate tools will streamline the removal process and prevent delays due to missing or inadequate tools.
Disconnect the Power Source
To ensure your safety during the removal process, it’s crucial to disconnect the power source from your Badger garbage disposal.
Identify the Power Source
Locate the electrical outlet or circuit breaker that supplies power to your garbage disposal. The outlet is typically under the sink, while the circuit breaker is usually in your home’s electrical panel.
Unplug the Outlet
If your garbage disposal is plugged into an outlet, simply unplug it. Use caution and avoid touching the wires.
Turn Off the Circuit Breaker
If your garbage disposal is connected to a circuit breaker, locate the corresponding breaker in your electrical panel. Flip the breaker to the “Off” position.
| Power Source Type | Disconnection Method |
|---|---|
| Outlet | Unplug the power cord. |
| Circuit Breaker | Flip the breaker to the “Off” position. |
Access the Disposal
1. Turn off the power to the disposal. This can be done at the circuit breaker or fuse box.
2. Open the cabinet doors under the sink.
3. Locate the disposal. It will be a cylindrical-shaped unit mounted under the sink. There will be a large screw-on ring that holds the disposal in place.
4. Place a bucket or trash can under the disposal to catch any water or debris that may spill out.
5. Using a screwdriver or wrench, loosen the screw-on ring that holds the disposal in place.
6. Once the ring is loose, you can pull the disposal down from the sink. Be careful, as it may be heavy.
Disconnect the Wiring
1. Once the disposal is removed from the sink, you will need to disconnect the wiring. There will be three wires that are connected to the disposal: a black wire, a white wire, and a green or bare copper wire.
2. Using a pair of pliers, disconnect the black and white wires from the terminals on the disposal.
3. Disconnect the green or bare copper wire from the ground screw on the disposal.
4. Once the wires are disconnected, you can remove the disposal from the sink.
Disassemble the Splash Guard
To disassemble the splash guard, follow these steps:
1. Locate the two tabs on the side of the splash guard.
2. Insert a screwdriver or other thin object into the slots on the tabs.
3. Push down on the tabs to release the splash guard.
4. Carefully lift the splash guard up and off the disposal.
Detailed Instructions for Step 4:
When lifting the splash guard up and off the disposal, be careful not to damage the electrical wires connected to the disposal. These wires are located on the underside of the splash guard and may be easily damaged if they are not handled carefully.
To avoid damaging the electrical wires, follow these guidelines:
- Support the splash guard with one hand while you lift it up with the other.
- Do not pull on the electrical wires.
- If the electrical wires are tangled, gently untangle them before lifting the splash guard.
| Step | Description |
|---|---|
| 1 | Locate the two tabs on the side of the splash guard. |
| 2 | Insert a screwdriver or other thin object into the slots on the tabs. |
| 3 | Push down on the tabs to release the splash guard. |
| 4 | Carefully lift the splash guard up and off the disposal. |
Disconnect the Mount Ring
The mount ring is the metal ring that secures the garbage disposal to the sink. To remove the Badger garbage disposal, you first need to disconnect the mount ring. Here’s how to do it:
- Turn off the power to the garbage disposal at the circuit breaker or fuse box.
- Unplug the garbage disposal from the power outlet.
- Place a bucket under the garbage disposal to catch any water that may leak out.
- Use a wrench to loosen the bolts that secure the mount ring to the sink.
- Carefully lift the garbage disposal up and off the mount ring. Be careful not to damage the sink or the garbage disposal.
| Bolt Size | Wrench Size |
|---|---|
| 1/2 inch | 12-inch adjustable wrench |
| 5/8 inch | 14-inch adjustable wrench |
| 3/4 inch | 16-inch adjustable wrench |
Remove the Disposal Body
Detach the electrical wiring.
Disconnect the drain hose by loosening the clamp and sliding it off carefully to avoid splashing.
Disconnect the dishwasher drain hose by unscrewing the fitting connecting it to the disposal.
Remove the mounting bracket.
– To do this, you will need to locate the three or four screws that hold the bracket in place and remove them.
Carefully lower the disposal by loosening the mounting screws and pulling it down.
Clean the sink flange area thoroughly before installing the new disposal.
Remove the Mounting Bracket
To remove the mounting bracket, you’ll need a Phillips head screwdriver. Follow these steps:
- Locate the two screws that hold the mounting bracket to the sink flange. These screws are typically located on the underside of the sink flange, near the edge of the sink.
- Use the Phillips head screwdriver to remove the two screws.
- Once the screws are removed, the mounting bracket should be loose. You can now lift the mounting bracket away from the sink flange.
- If the mounting bracket is stuck, you may need to use a putty knife or a flathead screwdriver to pry it loose.
- Once the mounting bracket is removed, you can now access the garbage disposal unit.
- Repeat the same steps on the other side of the mounting bracket to remove it completely.
- Once the mounting bracket is removed, you can now access the electrical wires, drain pipe, and water supply lines that are connected to the garbage disposal unit.
Clean the Mounting Area
Before removing the disposal, it’s important to clean the mounting area thoroughly. This will help prevent any debris or residue from getting into the new disposal and causing problems.
Materials Needed:
| Item | Quantity |
|---|---|
| Soft cloths or rags | 2-3 |
| Clean water | 1 bucket |
| White vinegar (optional) | 1/2 cup |
| Mild dish soap | A few drops |
Steps:
- Turn off the water supply: Locate the shut-off valves under the sink and close them.
- Unplug the disposal: Find the electrical outlet where the disposal is plugged in and disconnect it.
- Set up your cleaning station: Fill a bucket with clean water and add a few drops of dish soap. If desired, you can also add 1/2 cup of white vinegar to help remove odors.
- Wipe down the mounting area: Use a soft cloth or rag dipped in the cleaning solution to wipe down the mounting bolts, the mounting plate, and the surrounding area.
- Rinse the area: Dip a clean cloth or rag in clean water and rinse the mounting area thoroughly.
- Dry the area: Use a dry cloth or rag to thoroughly dry the mounting area.
- Inspect the mounting bolts: Check the mounting bolts for any damage or rust. If any bolts are damaged or rusted, they should be replaced.
- Lubricate the mounting bolts (optional): To make it easier to install the new disposal, you can apply a small amount of petroleum jelly or silicone lubricant to the threads of the mounting bolts. Be sure to only use a small amount and wipe off any excess.
Reinstall the Disposal
Now that you have the Badger garbage disposal removed, it’s time to reinstall it. If you have an electrical outlet under your sink, plug in the new disposal. If you do not have an outlet, you will need to run a new circuit to your sink. Once the disposal is plugged in, you can attach it to the sink drain using the mounting bracket.
Once the disposal is mounted, you can connect the drain line to the disposal. The drain line is the pipe that carries the wastewater from the sink to the disposal. To connect the drain line, simply slide the drain line onto the disposal’s drain connection. If necessary, you can use a screwdriver to tighten the drain line onto the disposal.
Once the drain line is connected, you can turn on the water supply to the sink. Check for leaks around the disposal and the drain line. If you find any leaks, tighten the connections until the leaks stop.
Turn on the disposal and let it run for a few minutes. This will help to prime the disposal and ensure that it is working properly. If the disposal is not working properly, check the circuit breaker to ensure that it is not tripped. If the circuit breaker is not tripped, you may need to call a plumber to help you troubleshoot the problem.
Restore Power and Verify Operation
1. Reset the Circuit Breaker or Replace the Fuse
Locate the circuit breaker or fuse box that controls the power to the Badger garbage disposal. If the breaker has tripped or the fuse has blown, reset or replace it accordingly.
2. Check for Loose Connections
Tighten any loose wire connections at the circuit breaker or fuse box, as well as any connections inside the Badger garbage disposal itself.
3. Isolate the Disposal from the Sink
Disconnect the Badger garbage disposal from the sink by unscrewing the mounting bracket that holds it in place.
4. Disconnect the Electrical Wires
Carefully disconnect the electrical wires from the Badger garbage disposal’s motor. Note the position of each wire for reconnecting later.
5. Remove the Badger Garbage Disposal
Lift the Badger garbage disposal straight up and out of the sink hole, taking care not to damage the pipes or wiring.
6. Clean the Sink Hole
Thoroughly clean the sink hole and remove any debris or obstructions that may have contributed to the disposal’s malfunction.
7. Install the New Badger Garbage Disposal
Insert the new Badger garbage disposal into the sink hole and secure it with the mounting bracket.
8. Reconnect the Electrical Wires
Reconnect the electrical wires to the Badger garbage disposal’s motor, ensuring that they are properly tightened.
9. Reinstall the Disposal into the Sink
Lower the Badger garbage disposal back into the sink hole and reconnect the mounting bracket.
10. Verify Operation
Turn on the Badger garbage disposal and run water through it to ensure it is operating correctly. Check for any leaks, unusual noises, or vibrations.
How To Remove A Badger Garbage Disposal
Removing a Badger garbage disposal is a relatively simple task that can be completed in a few minutes with the right tools. Here are the steps on how to do it:
- Turn off the power to the disposal. This can be done at the circuit breaker or fuse box.
- Disconnect the water supply to the disposal. This can be done by turning off the water valve under the sink.
- Loosen the mounting bolts. There are typically three or four mounting bolts that hold the disposal in place. Use a wrench to loosen these bolts.
- Disconnect the electrical wires. There are typically two electrical wires that connect the disposal to the power source. Use a screwdriver to disconnect these wires.
- Remove the disposal. Once the mounting bolts and electrical wires are disconnected, you can remove the disposal from the sink. Be careful not to drop it, as it is heavy.
People Also Ask About How To Remove A Badger Garbage Disposal
How do I remove theBadger garbage disposal housing?
To remove the Badger garbage disposal housing, you will need to disconnect the power to the disposal, disconnect the water supply, and remove the mounting bolts. Once the mounting bolts are removed, you can pull the housing straight up to remove it.
How do I remove the Badger garbage disposal motor?
To remove the Badger garbage disposal motor, you will need to remove the housing first. Once the housing is removed, you will see the motor. There are typically three or four bolts that hold the motor in place. Use a wrench to loosen these bolts and remove the motor.
How do I remove the Badger garbage disposal blades?
To remove the Badger garbage disposal blades, you will need to remove the motor first. Once the motor is removed, you will see the blades. There is a single bolt that holds the blades in place. Use a wrench to loosen this bolt and remove the blades.
